product details
SEQ v4+ Rack Mount Kit
Product ID: C-SEQ-02
SEQ v4+ rack mount kit. The 19 inch rack ears are milled for a perfect fit and are painted in the same color scheme as the SEQ v4+. Needs 136mm (3U and three millimeters) of rack height.
Weight: 100 grams
in stock
49.98 €
incl. VAT, excl. shipping
Recommended products
These additional products may be of interest:
SEQ v4+ Enhanced LH Essential Kit
K-SFE-01L
MIDIbox SEQ v4+ enhanced edition kit. LH case incl. rack kit (optional, needs 3U and 3mm of rack height), PCBs, UI parts, light|shields and L4 caps. Needs further parts to be completed.
929.99 €
incl. VAT, excl. shipping
SEQ v4+ Enhanced RH Essential Kit
K-SFE-01R
MIDIbox SEQ v4+ enhanced edition kit. RH case incl. rack kit (optional, needs 3U and 3mm of rack height), PCBs, UI parts, light|shields and L4 caps. Needs further parts to be completed.
929.99 €
incl. VAT, excl. shipping
19" Rack Installation Note
Yes, we utilized every last millimeter of the SEQ v4+ case! :)
Your SEQ v4+ will fit in a 19" rack and will occupy 3U - the SEQ v4+ front panel size is at exactly the allowed size of 133,3 mm for a 3U rack unit. But: there are a few case screws in the back of the SEQ v4+, that, depending on the neighboring synths/rack units might push the required height to 136 mm.
As many synths often don't use their full allowed height at that depth, this is very often unproblematic.
Note, that installing the SEQ v4+ is easier, when you install it in a rotating motion, install the bottom edge first, then "roll in" the top.
Also, normally enough space can be made available, as there is almost always a bit of "wiggle room" present, as many synths/rack units will not use their full allowed height over their full depth. Installation will also be easier, if you do not install the SEQ v4+ as the last unit in your 19" rack, but first leave e.g. the top space unoccupied, then install the SEQ v4+, and then install the rack unit on top.
If you still encounter vertical fit problems, you could also remove the problematic screws at the backside of the SEQ v4+, reducing its height requirement to the exactly allowed 133,3mm. These screws may not be needed for stability, if your SEQ v4+ is firmly installed in a 19" rack.
In short: your sequencer will fit in 3U, but we just wanted to tell you that it can be a close thing! :)
Your SEQ v4+ will fit in a 19" rack and will occupy 3U - the SEQ v4+ front panel size is at exactly the allowed size of 133,3 mm for a 3U rack unit. But: there are a few case screws in the back of the SEQ v4+, that, depending on the neighboring synths/rack units might push the required height to 136 mm.
As many synths often don't use their full allowed height at that depth, this is very often unproblematic.
Note, that installing the SEQ v4+ is easier, when you install it in a rotating motion, install the bottom edge first, then "roll in" the top.
Also, normally enough space can be made available, as there is almost always a bit of "wiggle room" present, as many synths/rack units will not use their full allowed height over their full depth. Installation will also be easier, if you do not install the SEQ v4+ as the last unit in your 19" rack, but first leave e.g. the top space unoccupied, then install the SEQ v4+, and then install the rack unit on top.
If you still encounter vertical fit problems, you could also remove the problematic screws at the backside of the SEQ v4+, reducing its height requirement to the exactly allowed 133,3mm. These screws may not be needed for stability, if your SEQ v4+ is firmly installed in a 19" rack.
In short: your sequencer will fit in 3U, but we just wanted to tell you that it can be a close thing! :)